DSM_4
|
|
- Indrek Nõmme
- 5 aastad tagasi
- Vaatused:
Väljavõte
1 Energiatarbimise juhtimine Energiaefektiivsus Argo Rosin
2
3
4 Säästuvõimalused Hotels 25% Offices 39% Restaurants 31% Residential 27% Hospitals 18% Schools / Unis 34% Shopping centres 49 %
5 Energiasääst hoone automatiseerimise kaudu
6 Kuidas saavutada energiaõhusus? Passiivsed meetmed Tõhus aparatuur ja paigaldus (10 to 15%) Madal energiatarve, soojustatud hoone... Aktiivsed meetmed Seadmete kasutuse optimeerimine (5 to 15%) Seadmete mitte kasutamisel, nende väljalülitamine, mootorite või kütte optimaalne reguleerimine Kuni 40% säästu on võimalik saavutada mootorite optimaalse juhtimisega, kasutades muundureid ja automaatikaseadmeid Kuni 30% säästu valgustuses on võimalik saavutada valgustuse optimaalse juhtimisega Püsiv jälgimine ja parandamine ehk hooldus (2 to 8%) Range hooldusprogramm, sh pidevad mõõtmised ning kõrvalekalletele reageerimine
7 Kuidas tagada energiatõhususe jätkusuutlikkus Mõõda (energiaarvestid, energikvaliteedi mõõtmisseadmed) Fikseeri prioriteedid (madala energiatarbega seadmed, isolatsioonimaterjalid, kvaliteet, töökindlus) Automatiseeri (hoone haldussüsteemid, valgustussüsteemid, mootorite juhtseadmed, kodu juhtseadmed, sagedusmuundurid) Jälgi ja parenda (Energiahaldussüsteemid ja - tarkvara, kaugseiresüsteemid)
8
9 Miks mõõtmistäpsus ja mõõteriista klass on oluline
10 Energia mõõtmisel 2 peamist eesmärki Lepingulised arved kliendi/rentniku ja energiatootja või edastaja vahel (In this case IEC for Classes 1 and 2 and IEC for Classes 0.5S and 0.2S become applicable to measure active energy. The full measurement chain CT, VT and measurement unit can reach a precision class Cl of 1 in low voltage, Cl 0.5 in medium voltage and 0.2 in high voltage, or even 0.1 in the future). Ettevõttesisene arveldamine eesmärgiga määrata iga toote tootmise energiakulu. (In this case of a precision class between 1 and 2 for the whole chain (CT, VT and measurement station) is sufficient).
11 Milleks kasutada kogutavaid andmeid? Elektrotehnilised andmed muudetakse mitmesuguseid eesmärke kandvaks infoks: muuta käitumist kasutajatel, et hallata energiat targalt ning lõpuks vähendab üldist energiakulu Suurendada töötajate/tarbijate tõhusust Vähendada energiatarbe kulusid aidata säästa energiat, mõistes kuidas energiat kasutatakse ja kuidas suurema energiatõhususe eesmärkidel seadmete kasutust ja protsesse optimeerida optimeerida ja suurendada võrgus oleva aparatuuri eluiga Vährndades ja vältides katkestusi või yagades paremat energiakvaliteeti suurendada protsesside tootlikkust.
12 Energiakasutajate harjumuste muutmine Kasutades kulude jaotamise aruanded, saab kontrollida kommunaalteenuste arvete õigsust, jagada osakondade põhiselt kulusid, jagada energiatarbimise osas vastutust organisatsiooni ehk ettevõtte tasandil, teha faktidel põhinevaid energiasäästlikke otsuseid. Eelnev toob kaasa energiassästlikkuse osa vastutustundlikuma käitumise ja seeläbi vähendadatakse kulusid.
13 Kuidas saavutada energiasääst Energiatarbimise vähendamise meetmed sama tulemuse saamiseks kasutada vähem energiat ja veendudes et ületarbimist poleks (näiteks inimtühjad täisvalgustuses koridorid). Üheks võimaluseks on kasutada lampe mis on sama energiatarbe juures suurema valgusviljakusega. Teiseks võimaluseks on ülevalgustatud aladel vähendada valgustust, grupeerides seadmeid või reguleerides valgust. Energiakulude vähendamise meede energiatarbimise nihutamise kaudu kõrge tariifiga perioodilt madala tariifiga perioodile. Sama kehtib ka tipu koormuste vähendamisel. Olemuselt väheneb energiaühiku hind Töökindluse meetmed tagamaks seadmete töö järjepidevuse vältides katkestusi ja seadmete süsteemide taaskäivitustest tingitud kadusid ja kulusid. Katkestused tingivad tootepartiide riknemisi, jms.
14 Igakülgne energiastrateegia
15 Mootorid ja nende asendamine 60% tarbitavast energiast kasutatakse mootorites Sõltuvalt võimsusest, kõrge kasuteguriga mootorid töötavad 1%- 10% tõhusamalt kui standardsed mootorid. Mootorid mis töötavad pikaajaliselt on otstarbekas asendada kõrge kasuteguriga mootoritega. Eriti need mootorid mis vajavad ümbermähkimist. Ümbermähitud mootorid on enamasti 3%-4% väiksema kasuteguriga ja vähemefektiivsed kui originaalmootorid. Mootorite kasutegur ja tõhusus on suurim kui nad töötavad 60%- 100% nimikoormusel. Kasutegur väheneb järsult kui koormus langeb alla 50%. Uuringud näitavad, et 1/3 mootoritest on üledimensioneeritud ja töötavad allpool 50% nimikoormust. Keskmine mootorite koormus on 60%. Suured madala võimsusteguriga mootorid võivad suurendada reaktiivenergia osakaalu tarbimises ja reaktiivenergia tasu. Mootorite vahetamisel tuleb lähtuda ka järelejäänud elueast. Arvestada tuleb seda, et vaatamata sellele, et mõned mootorid on üledimensioneeritud, kuid vähe ja harva koormatud ning tarbivad nii vähe energiat, et neid pole majanduslikult otstarbekas välja vahetada.
16 Muud meetmed mootoritele Improve active energy efficiency by simply turn off motors when they are not required. This may require improvements in automatic control, or education, monitoring and perhaps incentives for operators. If the operator of the motor is not accountable for its energy consumption, they are more likely to leave it running even when not in use. Check and if necessary correct shaft (võll) alignment, starting with the largest motors. Misaligned motor couplings waste energy and eventually lead to coupling failure and downtime. An angular offset of 0.6 mm in a pin coupling can result in a power loss of as much as 8%.
17 Pumbad, Ventilaatorid ja Sagedusmuundurid 63% mootorite poolt kasutatavast energiast kulutatakse pumpades ja ventilaatorites sõltumata tegelikust vajadusest, töötavad mootorid enamikel juhtudel täiskiirusel.
18 To change the flow or pressure in the system, there are a number of possible methods. The suitability will depend on the design of the fan or pump, e.g. Whether a pump is a positive displacement pump or rotodynamic pump, whether a fan is a centrifugal fan or axial fan. Multiple pumps or fans: This leads to step increase when additional pumps or fans are switched in, making fine control difficult. Usually there are efficiency losses as the real needs are somewhere between the possible steps. Stop/start control: This is only practical where intermittent flow is acceptable. Flow control valve: This uses a valve to reduce the flow by increased frictional resistance to the output of the pump. This wastes energy since the pump is producing a flow which is then cut back by the valve. In addition, pumps have a preferred operating range, and increasing the resistance by this method can force the pump to operate in a range where its efficiency is lower (wasting even more energy) and where its reliability is reduced. Damper: Similar in effect to a flow control valve in a pumping system, this reduces the flow by obstructing the output of the fan. This wastes energy since the fan is producing a flow which is then cut back by the damper. Bypass control: This technique keeps the pump running at full power and routes surplus fluid output from the pump back to the source. It allows a low value of flow to be achieved without risk of increasing the output pressure, but inefficiency is very high since the energy used to pump the surplus fluid is entirely wasted. Spillage valve: Similar in effect to a bypass control valve in a pumping system, this technique keeps the fan running at full power and vents surplus flow. Inefficiency is very high since the energy used to move the vented air or gas is entirely wasted. Variable pitch: Some fan designs allow the angle of the blades to be adapted to change the output. Inlet guide vane: these are structures using fins to improve or disrupt the routing of air or gas into a fan. In this way they increase or decrease the airflow going in and hence increase or decrease the output.
19 Fan and pump applications are governed by the affinity laws Vool (nt l/s) on proportsionaalne võlli kiirusega. Kiiruse vähendamine poole võrra vähendab voolu poole võrra Pressure or head is proportional to the square of shaft speed. Pool kiirust annab neljandiku rõhu. Half the shaft speed gives you quarter the pressure Võimsus on proportsionaalne võlli kiiruse kuubiga. Power is proportional to the cube of shaft speed. Half the shaft speed uses one eighth of the power. Hence half the flow uses one-eighth of the power
20 Theoretical power saving with a fan running at half speed
21 Power versus flow rate for the different fan control methods: downstream damper, inlet vanes, and variable speed (top to bottom)
22 Millest veel sõltub sääst? Tegelik saavutatav sääst sõltub ventilaatori või pumba ehitusest ja disainist, kasutegurist, mootori mõõtmetest, kasutamise ajast, elektrienergiamaksumusest.
23 The drive can be integrated into a variety of possible control methods Control by fixing pressure but varying flow: This uses a pressure sensor connected to the VSD which in turn varies the speed allowing the fan or pump to increase or decrease the flow required by the system. This is a common method in water supply schemes where constant pressure is required but water is required at different flows dependant on the number of users at any given time. This is also common on centralised cooling and distribution systems and in irrigation where a varying number of spray heads or irrigation sections are involved. Heating system control: In heating and cooling systems there is a requirement for flow to vary based on temperature. The VSD is controlled by a temperature sensor, which increases or decreases the flow of hot or cold liquid or air based on the actual temperature required by the process. This is similar to pressure control, where the flow also varies, but a constant temperature requirement from a temperature sensor replaces that from a pressure sensor. Control by fixing flow but varying pressure: Constant flow may be required in irrigation and water supply systems. Since the water levels both upstream and downstream of the pumping station can change, the pressure will be variable. Also many cooling, chiller, spraying and washing applications require a specific volume of water to be supplied even if the suction and delivery conditions vary. Typically suction conditions vary when the height of a suction reservoir or tank drops and delivery pressure can change if filters blind or if system resistance increases occur through blockages etc. A flowmeter is used to keep the flow rate constant, normally installed in the discharge line.
24 The benefits achieved include Reduced energy consumption and hence cost savings by replacing inefficient control methods or other obsolete components such as two-speed motors Better control and accuracy in achieving required flow and pressure Reduced noise and vibration, as the inverter allows fine adjustment of the speeds and so prevents the equipment running at a resonant frequency of the pipes or ductwork Increased lifecycle and improved reliability, for example, pumps that are operated in a throttled condition usually suffer from reduced useful life Simplified pipe or duct systems (elimination of dampers, control valves & by-pass lines) Soft start & stop creates less risk of transient effects in the electrical network or mechanical stress on the rotating parts of the pump or fan. This also reduces water hammer in pumps, because the drive provides smooth acceleration and deceleration instead of abrupt speed variations Reduced maintenance
25 Valgustus Sõltuvalt hoone kasutamisest võib valgustuse energiatarve olla üle 35% kogutarbest. Valgustuse juhtimine on üks lihtsamaid võimalusi säästa energiakulusid väikeste investeerimiskuludega. Valgustuse juhtimine on üks enimlevinud energiasäästu meetmeid.
26 Lighting control Some of the simplest methods include: Timer switches to turn off lights after a fixed period has passed. Timers are best deployed in areas where occupancy is well defined (e.g. in hotel corridors where the time for a person to pass through is predictable). Occupancy sensors / movement detectors to turn off lights when no movement has been detected for a certain period. Occupancy sensors are best deployed in offices, storerooms, stairwells, kitchens and bathrooms where the use of the facilities cannot be predicted with a high degree of accuracy during the day. Photoelectric cells / daylight harvesting sensors to control lights near windows. When bright exterior light is available, lamps are turned off or dimmed. Programmable timers to switch lights on and off at predetermined times (e.g. Shop fronts, ensure office lights are turned off at nights and weekends). Dimmable lights to maintain a low level of illumination at off-peak periods (e.g. A car parking lot which needs to be fully illuminated during peak use, perhaps until midnight, but which can have lower ambient illumination from midnight until dawn) Voltage regulators to optimize the power consumed. Ballasts perform this function on fluorescent lighting. Voltage regulators are also available for other lighting types such as high pressure sodium lamps.
27 Tarbimise juhtimine
28 Load management strategies Peak demand avoidance - The objective is to keep the total energy consumed in each period below the limit. All loads in a facility are defined in one of three categories: critical, essential, and non-essential loads. Usually only non-essential loads are shed, and the order of shedding can be configured. Providing the customer has enough non-essential loads to be able to impact their peak consumption, it may be possible to reduce the demand charge by as much as 10% to 30%. Demand charge can be up to 60% of the bill. The application usually pays for itself in one year or less.
29
30
31 Load management strategies Load scheduling - Utilities often have different rates that apply for different times of the day. During normal daily business hours, the rates are the highest. Many users shift, or reschedule loads to take advantage of lower rates. These are loads that are not time sensitive or critical.. Demand response (curtailment) Demand response is a means to manage the demand from customers taking supply conditions into account. Utilities may offer financial incentives to customers to reduce load during periods when the utility does not have the distribution capacity to handle the total demand. A curtailment is activated following a notification by phone or via a signal output from the utility revenue meter. Typically there is 30 to 60 minutes advance notice. The customer systematically reduces load until the curtailment level is obtained, either by manually reducing or shutting off loads or by an automated PLC controlled system. The utility or aggregator then signals the start of the curtailment period. After the curtailment period is complete, the utility or aggregator signals the end of the curtailment period. The customer may then re-establish normal facility loading and production. On-site generation
32 Koormuste haldamise strateegiad Demand response (curtailment) Demand response is a means to manage the demand from customers taking supply conditions into account. Utilities may offer financial incentives to customers to reduce load during periods when the utility does not have the distribution capacity to handle the total demand. In some countries, third-party aggregators may manage schemes that monitor the network capacity and the realtime price of electricity on the network. Participants in the scheme receive incentives to shed load, creating capacity which the aggregator can sell into the network. In each case, the utility or aggregator offers a contract including an agreement from the customer to reduce the kw consumption at their site down to a predetermined level when notified. These contracts may contain both emergency curtailments (when the participants in the scheme must comply or face penalties) and opt-in curtailments (where participants can evaluate the specific conditions for that particular curtailment and decide whether or not to accept). Automated demand response control applications usually pay for themselves in one year or less.
33 Nõudluse vastus - Demand response Demand response is a means to manage the demand from customers taking supply conditions into account. Utilities may offer financial incentives to customers to reduce load during periods when the utility does not have the distribution capacity to handle the total demand. A curtailment is activated following a notification by phone or via a signal output from the utility revenue meter. Typically there is 30 to 60 minutes advance notice. The customer systematically reduces load until the curtailment level is obtained, either by manually reducing or shutting off loads or by an automated PLC controlled system. The utility or aggregator then signals the start of the curtailment period. After the curtailment period is complete, the utility or aggregator signals the end of the curtailment period. The customer may then re-establish normal facility loading and production. The return on investment from demand response schemes will vary depending on local tariff rates and electricity market. The incentive generally takes the form of a credit for the demand reduction during the response period. If the customer has enough non-essential loads to be able to impact peak consumption, he may be able to benefit from incentives that in effect reduce the cost per unit by as much as 30%.
34 Load management strategies On-site generation On-site generation increases the flexibility available to facility operators. Instead of shedding loads, on-site generation can provide the power required to keep running during a period of peak avoidance or demand curtailment. The automated control system can be extended to integrate control of on-site generation facilities into the scheme. If the customer is buying electricity from a supplier at a time-of-use rate, the control system can be configured to continuously monitor the current cost of electricity from the supplier and compare it to the cost of energy generated on site using another fuel source. When the cost of electricity rises above the cost of using the generator (replacing the fuel), the control scheme automatically shifts load to the on-site generation. When the cost falls, load is shifted back to the supply utility.
35 Power factor correction Kui elektrienergia tarnija maksustab reaktiivvõimsust, on võimalik võimsusteguri korrektsiooni rakendades saada märkimisväärset kokkuhoidu elektriarvetelt Lahendused või meetmed võimsusteguri parandamiseks on tavaliselt passivset laadi ja ei too kaasa muudatusi olemasolevates protsessides ja töötajate käitumises. Investeeringute tasuvusaeg on sageli lühem kui üks aasta.
36 Power factor calculation The power factor is the ratio of kw to kva. The closer the power factor approaches its maximum possible value of 1, the greater the benefit to consumer and supplier. PF = P (kw) / S (kva), kus P = Active power and S = Apparent power
37 Power factor improvement allows the use of smaller transformers, the use of switchgear and cables, etc. reducing of power losses and voltage drop in an installation reducing of electricity bills
38 Power diagram S 2 = P 2 + Q 2
39 Example in the calculation of active and reactive power
40 Values of cos ϕ and tan ϕ for commonly-used equipment
41 Multiplying factor for cable size as a function of cos ϕ
42 Technical/economic optimization Losses in cables are proportional to the current squared, and are measured by the kwh meter of the installation. Reduction of the total current in a conductor by 10% for example, will reduce the losses by almost 20%. Power factor correction capacitors reduce or even cancel completely the (inductive) reactive current in upstream conductors, thereby reducing or eliminating voltage drops. Over compensation will produce a voltage rise at the capacitor level. By improving the power factor of a load supplied from a transformer, the current through the transformer will be reduced, thereby allowing more load to be added. In practice, it may be less expensive to improve the power factor, than to replace the transformer by a larger unit.
43 Kompenseerimise printsiip Q C = P (tanϕ tanϕ' ) = P ( 1 (cosϕ) (cosϕ') 2 1)
44 Harmonic filtering Many solutions to improve efficient use of electricity can have side effects, bring harmonics into the electrical network. High-efficiency motors, variable speed drives, electronic ballasts for fluorescent lights, and computers can all generate electrical pollution which can have significant effects. Harmonics can create transient overvoltage conditions that cause protection relays to trip and result in production downtime. They increase heat and vibration and thereby decrease efficiency and shorten life of neutral conductors, transformers, motors and generators. Power factor correction capacitors may magnify harmonics, and can suffer from overloading and premature aging.
45 Disturbances caused by harmonics Overloads on distribution networks due to the increase in rms current Overloads in neutral conductors due to the cumulative increase in third-order harmonics created by single-phase loads Overloads, vibration and premature ageing of generators, transformers and motors as well as increased transformer hum Overloads and premature ageing of power-factor correction capacitors Distortion of the supply voltage that can disturb sensitive loads Disturbances in communication networks and on telephone lines
46 Harmonics have a major economic impact: Premature ageing of equipment means it must be replaced sooner unless oversized right from the start Overloads on the distribution network can require higher subscribed power levels and increase losses Distortion of current waveforms provokes nuisance tripping that can stop production
47 Harmonics have major economic effects in installations: Increases in energy costs Premature ageing of equipment Production losses
48 Maximum permissible harmonic levels
49 Main effects of harmonics in installations Resonance Increased losses (in conductors, asynchronous machines, transformers, capacitors) Overloads on equipment (Generators, Uninterruptible power systems, Transformers, Asynchronous machines, Capacitors, Neutral conductors
50 Harmonic management U h = Z h I h When the harmonic current of order h flows through impedance Zh, it creates a harmonic voltage Uh.
51 Resonance Ls = Supply inductance (upstream network + transformer + line) C = Capacitance of the power factor correction capacitors R = Resistance of the linear loads Ih = Harmonic current To avoid resonance, antiharmonic coils can be installed in series with the capacitors.
52 Increased losses THD - Total harmonic distortion
53 Overloads - Transformers Derating required for a transformer supplying electronic loads
54 Derating factor for transformers If the transformer supplies an overall load comprising 40% of electronic loads, it must be derated by 40%. Standard UTE C provides a derating factor for transformers as a function of the harmonic currents. Current with a rectangular waveform (1/h spectrum (1)): k = 0.86 Frequency-converter current (THD 50%): k = 0.80
55 Asynchronous machines Standard IEC defines a weighted harmonic factor (Harmonic voltage factor) for which the equation and maximum value are provided below
56 Power values and harmonics Reactive power :Q = U1 x I1 x sinϕ1 When harmonics are present, the distortion power D is defined as D = (S 2 - P 2 - Q 2 ) 1/2 The individual harmonic distortion is defined as the percentage of harmonics for order h with respect to the fundamental
57 Power values and harmonics The rms value of the voltage and current can be calculated as a function of the rms value of the various harmonic orders The term THD means Total Harmonic Distortion and is a widely used notion in defining the level of harmonic content in alternating signals. For a signal y, the THD is defined as
58 Power values and harmonics The equation below is equivalent to the above, but easier and more direct when the total rms value is available For voltage harmonics, the equation is
59 Relation between power factor and THD
60 To limit the propagation of harmonics in the distribution network
61 To limit the propagation of harmonics in the distribution network
62 To limit the propagation of harmonics in the distribution network
63 To limit the propagation of harmonics in the distribution network
64 To limit the propagation of harmonics in the distribution network Install reactors When variable-speed drives are supplied, it is possible to smooth the current by installing line reactors. By increasing the impedance of the supply circuit, the harmonic current is limited. Installation of harmonic suppression reactors on capacitor banks increases the impedance of the reactor/capacitor combination for high-order harmonics. This avoids resonance and protects the capacitors. Select the suitable system earthing arrangement TNC system In the TNC system, a single conductor (PEN) provides protection in the event of an earth fault and the flow of unbalance currents. Under steady-state conditions, the harmonic currents flow in the PEN. The latter, however, has a certain impedance with as a result slight differences in potential (a few volts) between devices that can cause electronic equipment to malfunction. The TNC system must therefore be reserved for the supply of power circuits at the head of the installation and must not be used to supply sensitive loads. TNS system This system is recommended if harmonics are present. The neutral conductor and the protection conductor PE are completely separate and the potential throughout the distribution network is therefore more uniform.
Microsoft PowerPoint - RRand_MEMS.ppt
MEMS sensorid Rait Rand 1 Sissejuhatus MEMS MEMS : Micro-electromechanical systems 1974.a. rõhusensor masstoodangus 1988.a. mikromehhaanika ühendati elektroonikaga Süsteemina Sensorsüsteemid Aktuaatorsüsteemid
RohkemMicrosoft Word - EVS_ISO_IEC_27001;2014_et_esilehed.doc
EESTI STANDARD EVS-ISO/IEC 27001:2014 INFOTEHNOLOOGIA Turbemeetodid Infoturbe halduse süsteemid Nõuded Information technology Security techniques Information security management systems Requirements (ISO/IEC
Rohkem(Tõrked ja töökindlus \(2\))
Elektriseadmete tõrked ja töökindlus Click to edit Master title style 2016 sügis 2 Prof. Tõnu Lehtla VII-403, tel.6203 700 http://www.ttu.ee/energeetikateaduskond/elektrotehnika-instituut/ Kursuse sisu
RohkemVõrguinverterite valik ja kasutusala päikeseelektrijaamades Robert Mägi insener
Võrguinverterite valik ja kasutusala päikeseelektrijaamades Robert Mägi insener Robert Mägi o Õpingud: Riga Technical University o Haridus: MSc (Electrical Engineering) MSc (Automatic Telecommunications)
RohkemREQUEST FOR AN ASSIGNMENT OF LEI (fond) LEI KOODI MÄÄRAMISE TAOTLUS (fond) 1. FUND DATA / FONDI ANDMED: Legal Name / Ametlik nimi: Other Fund Names /
REQUEST FOR AN ASSIGNMENT OF LEI (fond) LEI KOODI MÄÄRAMISE TAOTLUS (fond) 1. FUND DATA / FONDI ANDMED: Legal Name / Ametlik nimi: Other Fund Names / Fondi teised nimed: Business Register Number / Äriregistri
RohkemSissejuhatus GRADE metoodikasse
Sissejuhatus GRADE metoodikasse Eriline tänu: Holger Schünemann ja GRADE working group www.gradeworkinggroup.org Kaja-Triin Laisaar TÜ peremeditsiini ja rahvatervishoiu instituut kaja-triin.laisaar@ut.ee
RohkemEESTI STANDARD EVS-EN 1790:1999 This document is a preview generated by EVS Teemärgistusmaterjalid. Kasutusvalmid teekattemärgised Road marking materi
EESTI STANDARD EVS-EN 1790:1999 Teemärgistusmaterjalid. Kasutusvalmid teekattemärgised Road marking materials - Preformed road markings EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev
RohkemPowerPoint Presentation
Miks liituda projektiga LIFE Fit for REACH? Karin Viipsi Henkel Balti OÜ (Henkel Makroflex AS) Infopäev ettevõtetele, 09.11.2016 Sisukord Ettevõtte tutvustus Ettevõtte eesmärk projektis Mida on varasemalt
RohkemPpt [Read-Only]
EL 2020 strateegia eesmärkidest, mis puudutab varajast koolist väljalangemist ja selle vähendamist EL 2020 strateegia eesmärkidest, mis puudutab madala haridustasemega noorte osakaalu vähendamist Madal
RohkemEESTI STANDARD EVS-EN :2000 This document is a preview generated by EVS Terastraat ja traattooted piirete valmistamiseks. Osa 4: Terastraadist
EESTI STANDARD EVS-EN 10223-4:2000 Terastraat ja traattooted piirete valmistamiseks. Osa 4: Terastraadist keevitatud võrkpiire Steel wire and wire products for fences - Part 4: Steel wire welded mesh fencing
RohkemKehtiv alates Vormi TSD lisa 3 Applicable from Annex 3 of Form 3 Unofficial translation Maksu- ja Tolliamet Estonian Tax and Cus
Kehtiv alates 01.01.2018 Vormi TSD lisa 3 Applicable from 01.01.2018 Annex 3 of Form 3 Unofficial translation Maksu- ja Tolliamet Estonian Tax and Customs Board MITTERESIDENDIST JURIIDILISE ISIKU PÜSIVAST
RohkemMicrosoft PowerPoint - Kalle Kukk, Estfeed.pptx
Keskne platvorm energiateenuste arendamiseks Estfeed Kalle Kukk Elering AS Strateegiajuht kalle.kukk@elering.ee 27.03.2014 110-330 kv liinid 5223 km kõrgepinge õhuja kaabelliine Ülepiirilised ühendused
RohkemMicrosoft Word - EVS_ISO_31000;2010_et_esilehed
EESTI STANDARD EVS-ISO RISKIJUHTIMINE Põhimõtted ja juhised Risk management Principles and guidelines EVS-ISO EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard EVS-ISO Riskijuhtimine. Põhimõtted
Rohkemtallinn arvudes 2003.indd
15 16 Ilmastik ja keskkond 1. Õhutemperatuur, 2003... 18 2. Päikesepaiste, 2003.... 19 3. Sademed, 2003... 20 4. Keskmine tuule kiirus, 2003.. 21 5. Looduskaitse load, 2003..... 22 6. Õhusaaste paiksetest
RohkemKuidas, kus ja milleks me kujundame poliitikaid Kuidas mõjutavad meid poliitikad ja instrumendid Euroopa Liidu ja riigi tasandil Heli Laarmann Sotsiaa
Kuidas, kus ja milleks me kujundame poliitikaid Kuidas mõjutavad meid poliitikad ja instrumendid Euroopa Liidu ja riigi tasandil Heli Laarmann Sotsiaalministeerium Rahvatervise osakond 15.06.2018 Mis on
RohkemJätkuv UNIKAALSUS viib uuendusteni LED-TOODETE KATALOOG 2016
Jätkuv UNIKAALSUS viib uuendusteni LED-TOODETE KATALOOG 2016 02 4 B to C Klassikaline/hämardatav elektripirn... 06- Klassikaline/hämardatav PAR16... Klassikaline MR16... Klassikaline/hämardatav küünal...
RohkemPiima ja tooraine pakkumise tulevik kogu maailmas Erilise fookusega rasvadel ja proteiinidel Christophe Lafougere, CEO Gira Rakvere, 3rd of October 20
Piima ja tooraine pakkumise tulevik kogu maailmas Erilise fookusega rasvadel ja proteiinidel Christophe Lafougere, CEO Gira Rakvere, 3rd of October 2018 clafougere@girafood.com Tel: +(33) 4 50 40 24 00
RohkemTitle here
Eleringi toimetised nr 2/2016 (13) BALTIC REGIONAL GAS MARKET STUDY Balti regionaalse gaasituru uuring Tallinn 2016 BALTIC REGIONAL GAS MARKET STUDY Balti regionaalse gaasituru uuring Tallinn 2016 Elering
RohkemPealkiri
Graafilised mudelid ja nende koostamise vahendid MS Visio MYSQL Workbench (DB Designer) ER/Studio Data Architect Sybase PowerDesigner GRAAFILINE MODELLEERIMINE Mudel ja modelleerimine 3 11/3/2015 Matemaatiline
RohkemKuidas hoida tervist töökohal?
Kuidas hoida tervist töökohal? Kristjan Port, TLU 25.04.2017 Tööinspektsiooni konverents Kas aeg tapab?. Mis on tervis? Teadmatus võib olla ratsionaalne. On olukordi milles teadmiste hankimise kulud ületavad
RohkemEST_Web_QIG_TU-P1284.cdr
Lühike paigaldusjuhend TU-P1284 Table Sisukord of Contents Eesti... 1. Enne alustamist... 2. Riistvara paigaldamine... 3. Draiveri paigaldamine... 4. Paigaldamise kontrollimine... 1 1 2 3 4 Tõrkeotsing...
RohkemSAF 7 demo paigaldus. 1.Eeldused SAF 7 demo vajab 32- või 64-bitist Windows 7, Window 8, Windows 10, Windows Server 2008 R2, Windows Server 2012, Wind
SAF 7 demo paigaldus. 1.Eeldused SAF 7 demo vajab 32- või 64-bitist Windows 7, Window 8, Windows 10, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016 või Windows
RohkemKommunikatsiooniteenuste arendus IRT0080 Loeng 5/2013 Satelliitside teenused Avo Ots telekommunikatsiooni õppetool TTÜ raadio- ja sidetehnika instituu
Kommunikatsiooniteenuste arendus IRT0080 Loeng 5/2013 Satelliitside teenused Avo Ots telekommunikatsiooni õppetool TTÜ raadio- ja sidetehnika instituut avo.ots@ttu.ee 1 Võrdlus teiste sideviisidega 2 Satelliitside
RohkemSQL
SQL Kuues loeng 3GL inside 4GL Protseduurid Funktsioonid Tavalised Funktsioonid (üks väljund) Ilma väljundita Protseduurid Viitargumentide kasutamise võimalus Tabel-väljundiga Protseduurid Create function
RohkemMicrosoft Word - MM_17 13[1] lisa 3
Lisa 3 majandus- ja kommunikatsiooniministri 2006.a määrusele nr CEPT ELEKTROONILISE SIDE KOMITEE OTSUSED JA SOOVITUSED, ITU SOOVITUSED, EUROOPA LIIDU DIREKTIIVID JA OTSUSED, RAHVUSVAHELISED KOKKULEPPED,
RohkemMicrosoft Word - Lisa 4_Kohtususteemide vordlus
RIIGIKOHTU ESIMEHE 2011. A ETTEKANNE RIIGIKOGULE LISA 4 Eesti kohtusüsteem Euroopas Euroopa Nõukogu Ministrite Komitee on ellu kutsunud Tõhusa õigusemõistmise Euroopa komisjoni (CEPEJ), mis koosneb 47
RohkemPowakaddy
Powakaddy PowaKaddy Sport http://www.powakaddy.com/index.php/electric-trolleys/sport.html Elektrilised kärud liitium või tavalise akuga / Electrical trolleys with lithium or acid battery Liitium akuga
RohkemScanned Image
EESTI MAAILMAS 21. SAJANDI KÜNNISEL EESTI MAAILMAS 21. SAJANDI KÜNNISEL TARTU ÜLIKOOL EESTI MAAILMAS 21. SAJANDI KÜNNISEL Eesti Vabariigi presidendi Lennart Meri 70. sünnipäevale pühendatud konverentsi
RohkemMicrosoft PowerPoint - BPP_MLHvaade_juuni2012 (2)
Balti pakendi protseduur MLH kogemus Iivi Ammon, Ravimitootjate Liit Ravimiameti infopäev 13.06.2012 Eeltöö ja protseduuri algus Päev -30 MLH esindajad kolmes riigis jõuavad arusaamani Balti pakendi protseduuri
RohkemPowerPoint Presentation
Ülevaade Mehhaanika ja elektroonika tooted, elektromehaanilised koosted 30 aastat kogemust Müügikäive 2018 MEUR 15,4 2 tootmisüksust Euroopas HYRLES OY Soome tehas Asutatud 1989 Tootmine 8500 m2 Personal
Rohkemrp_ IS_3
Page 1 of 5 Üldine informatsioon Kummelitee Exemption Flags Toote nimi Exempt from Artwork Exempt from NEP Reporting Country Lipton Brand Name CAMOMILE Product Name Legal Description Country Kummelitee
RohkemKliiniliste soovituste koostamine
Kliiniliste soovituste koostamine Eriline tänu: Holger Schünemann ja GRADE working group www.gradeworkinggroup.org Kaja-Triin Laisaar TÜ peremeditsiini ja rahvatervishoiu instituut kaja-triin.laisaar@ut.ee
RohkemVäljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: Avaldamismärge: RT II 2008, 17, 49 Eesti Vabarii
Väljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: 22.04.2008 Avaldamismärge: RT II 2008, 17, 49 Eesti Vabariigi ja Soome Vabariigi viisaküsimustes Soome Vabariigi
RohkemCOM(2004)651/F1 - ET
EUROOPA ÜHENDUSTE KOMISJON Brüssel 11.10.2004 KOM(2004) 651 lõplik KOMISJONI TEATIS EUROOPA PARLAMENDILE JA NÕUKOGULE Euroopa lepinguõigus ja ühenduse õigustiku muutmine: tulevikuplaanid ET ET 1. SISSEJUHATUS
RohkemMicrosoft Word - Loppukilpailu2015_16_tehtavat_viro_1
Põhikooli matemaatika võistlus Lõppvõistlus reedel 22.1.2016 OSA 1 Lahendamiseks aega 30 min Punkte 20 Selles osas kalkulaatorit ei kasutata. Lühikesed lahendused ja vajalikud joonised teha samale paberile.
RohkemKUULA & KORDA INGLISE KEEL 1
KUULA & KORDA INGLISE KEEL 1 KUULA JA KORDA Inglise keel 1 Koostanud Kaidi Peets Teksti lugenud Sheila Süda (eesti keel) Michael Haagensen (inglise keel) Kujundanud Kertu Peet OÜ Adelante Koolitus, 2018
RohkemE-õppe ajalugu
Koolituskeskkonnad MTAT.03.142 avaloeng Anne Villems September 2014.a. Põhiterminid Koolituskeskkonnad (Learning environments) IKT hariduses (ICT in education) E-õpe (e-learning) Kaugõpe (distance learning)
RohkemVäljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: Avaldamismärge: RT II 2010, 18, 90 Eesti Vabarii
Väljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: 04.06.2010 Avaldamismärge: RT II 2010, 18, 90 Eesti Vabariigi ja Soome Vabariigi viisaküsimustes esindamise kokkulepete
RohkemEESTI STANDARD EVS-ISO 24510:2008 This document is a preview generated by EVS JOOGIVEE- JA KANALISATSIOONITEENUSTEGA SEOTUD TEGEVUSED Juhised joogivee
EESTI STANDARD JOOGIVEE- JA KANALISATSIOONITEENUSTEGA SEOTUD TEGEVUSED Juhised joogivee- ja kanalisatsiooniteenuste hindamiseks ning parandamiseks kasutajale Activities relating to drinking water and wastewater
RohkemRahvusvaheline motokross Baltimere Karikas 2015 Soome Eesti Läti Leedu Kooskõlastanud: EMF-i alajuht; Kinnitanud: EMF peasekretär 1. Aeg ja koht: 18.0
Rahvusvaheline motokross Baltimere Karikas 2015 Soome Eesti Läti Leedu Kooskõlastanud: EMF-i alajuht; Kinnitanud: EMF peasekretär 1. Aeg ja koht: 18.04.2015, Eesti, Holstre-Nõmme motokeskus. (58 o 18 56.36
RohkemEVS standardi alusfail
TEHNILINE SPETSIFIKATSIOON Avaldatud eesti keeles: november 2018 AUTOMAATNE TULEKAHJUSIGNALISATSIOONISÜSTEEM Osa 14: Planeerimise, projekteerimise, paigaldamise, ülevaatuse, kasutamise ja hoolduse eeskiri
RohkemEST_web_QIG_TU-PS2(V1.1R).cdr
Lühike paigaldusjuhend TU-PS2 Table Sisukord of Contents Eesti... 1. Enne alustamist... 2. Riistvara paigaldamine... 1 1 2 Tõrkeotsing... 5 Version 11.21.2007 1. Enne alustamist Pakendi sisu TU-PS2 Lühike
Rohkemuntitled
Riistvara kirjelduskeel VHDL L4, L5. Riistvara kirjelduskeel VHDL L6. Mäluga süsteemid VHDL-s L7. VHDL ja süntees 1 Atribuudid Atribuut on väärtus, funktsioon, tüüp, vahemik, signaal või konstant, mida
RohkemVorm_V1_2014_18.02
Kehtiv alates jaanuar 2014 Applicable from 2014 Maksu- ja Tolliamet Tax and Customs Board Vorm V1 Form V1 MITTERESIDENDI JA LEPINGULISE INVESTEERIMISFONDI EESTIS ASUVA VARA VÕÕRANDAMISEST SAADUD KASU DEKLARATSIOON
RohkemIII OSA. RAADIOSAGEDUSALA 3600 MHz 1000 GHz Rahvusvahelise Telekommunikatsiooni Liidu konventsiooni ja põhikirja täiendavate raadioeeskirjadega määrat
III OSA. RAADIOSAGEDUSALA 3600 MHz 1000 GHz Rahvusvahelise Telekommunikatsiooni Liidu konventsiooni ja põhikirja täiendavate raadioeeskirjadega määratud raadiosagedusala kasutusrežiim ja otstarve 3600
RohkemInglise keele ainekava 5.klassile Kuu Õpitulemused Õppesisu Kohustuslik hindamine September 1. Räägib loomadest. Vaba aeg. Animals (Wild life 2. Kuula
Inglise keele ainekava 5.klassile Kuu Õpitulemused Õppesisu Kohustuslik hindamine September 1. Räägib loomadest. Vaba aeg. Animals (Wild life 2. Kuulab, loeb ja jutustab dialooge and pets) Sõnavara teemadel
RohkemMicrosoft Word - C035736e.doc
EESTI STANDARD Süsteemi- ja tarkvaratehnika Süsteemide ja tarkvara kvaliteedinõuded ja kvaliteedi hindamine (SQuaRE) Andmekvaliteedi mudel Software engineering Software product Quality Requirements and
RohkemPrint\A4\QualifyReduced.pmt
Warm up - minutes 0.0.0 0: Sorted on Best time Practice started at :: Best Tm s In Class Entrant Make Mia-Mariette PANKRATOV 0. TARK Racing Birel 0 Reigo HUNT.0 0. Viljandi KEK Kosmic Marko LEOTOOTS..
RohkemAvatud ja läbipaistev e-riik: Ees6 kui rajaleidja Andrus Kaarelson RIA peadirektori asetäitja riigi infosüsteemi alal 10. oktoober 2017
Avatud ja läbipaistev e-riik: Ees6 kui rajaleidja Andrus Kaarelson RIA peadirektori asetäitja riigi infosüsteemi alal 10. oktoober 2017 Eesti kui rajaleidja e-riigi rajamisel E-teenused meie elu loomulik
RohkemLp. firmajuht!
Lp. firmajuht! Veebruar, 1998 Meil on meeldiv võimalus kutsuda Teie firmat osalema meditsiinitehnika ja farmaatsiatoodete näitusele Eesti Arstide Päevad 98, mis toimub 24.-25. aprillil 1998. a. Tartus.
RohkemSlide 1
TÖÖTUBA: ÕPIRÄNDE TUNNISTUSE TÄITMINE Margit Paakspuu 5163 Töötoa ülesehitus 1. Kellele ja milleks me õpirände tunnistusi väljastame? 2. Õpirände tunnistuse väljastamise protseduur 3. Õpirände tunnistuse
RohkemTuuleenergeetika võimalikkusest Eestis
Noppeid energeetikast 9.03.2011 Võimsus = = 3 MW 1500 x 2 kw 272727 x 11 W 1 MW=1000 kw=1 000 000 W Energia x = 2000 W 2h 4 kwh 1 kwh = 1,4 kg põlevkivi 1 kwh = 160 g šokolaadi Istudes ja õppides kulutate
RohkemEESTI STANDARD EVS-ISO/IEC 25021:2014 This document is a preview generated by EVS SÜSTEEMI- JA TARKVARATEHNIKA Süsteemide ja tarkvara kvaliteedinõuded
EESTI STANDARD SÜSTEEMI- JA TARKVARATEHNIKA Süsteemide ja tarkvara kvaliteedinõuded ja kvaliteedi hindamine (SQuaRE) Kvaliteedinäitajate elemendid Systems and software engineering Systems and software
RohkemANOVA Ühefaktoriline dispersioonanalüüs Treeningu sagedus nädalas Kaal FAKTOR UURITAV TUNNUS Mitmemõõtmeline statistika Kairi Osula 2017/kevad
ANOVA Ühefaktoriline dispersioonanalüüs Treeningu sagedus nädalas Kaal FAKTOR UURITAV TUNNUS Factorial ANOVA Mitmefaktoriline dispersioonanalüüs FAKTOR FAKTOR Treeningu sagedus nädalas Kalorite kogus Kaal
RohkemPowerPoint Presentation
MILLISES KESKKONNAS TAHAME VEETA 90% OMA AJAST EHK ÜLEVAADE MADALA ENERGIATARBEGA HOONETE NIMETUSTEST NING TRENDIDEST MADALA ENERGIATARBEGA EHITUSE OSAS Lauri Tammiste Eesti Arengufondi energia ja rohemajanduse
RohkemVäljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: Avaldamismärge: RT II 2008, 29, 84 Eesti Vabarii
Väljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: 01.08.2008 Avaldamismärge: RT II 2008, 29, 84 Eesti Vabariigi ja Soome Vabariigi viisaküsimustes Iraani Islamivabariigis
RohkemVäljaandja: EÜEVAN Akti liik: otsus Teksti liik: algtekst Avaldamismärge: RT II 2002, 4, 7 Otsus nr 7/2001 (UE-EE 813/01), millega võetakse vastu ting
Väljaandja: EÜEVAN Akti liik: otsus Teksti liik: algtekst Avaldamismärge: RT II 2002, 4, 7 Otsus nr 7/2001 (UE-EE 813/01), millega võetakse vastu tingimused Eesti Vabariigi osalemiseks programmis Kultuur
RohkemErasmus+: Euroopa Noored eraldatud toetused 2015 KA1 NOORTE JA NOORSOOTÖÖTAJATE ÕPIRÄNNE NOORTEVAHETUSED R1 1. taotlusvoor Taotleja Taotluse pealkiri
Erasmus+: Euroopa Noored eraldatud toetused 2015 KA1 NOORTE JA NOORSOOTÖÖTAJATE ÕPIRÄNNE NOORTEVAHETUSED Loomade Nimel Baltic Animal Rights Gathering 2015 13270 Xploreworld Health in Action 20682 Ahtme
RohkemMicrosoft Word - 08.doc
EESTI VÕIMALIK RAHVAARV JA VANUSKOOSSEIS AASTANI 2050 Aasa Maamägi Rahvastikustatistika talituse juhtivstatistik 2000. aasta rahva- ja eluruumide loenduse alusel Statistikaametis koostatud vaadeldava ajaperioodi
RohkemKommunikatsiooniteenuste arendus (IRT0080) loeng 8/2014 Võrkude haldus Avo 1
Kommunikatsiooniteenuste arendus (IRT0080) loeng 8/2014 Võrkude haldus Avo avo.ots@ttu.ee 1 Infovood (voice data) 2 Standardimine ja tähistamine 3 Cross Layer Design Wireless Networking Architecture: Connection
RohkemVäljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: Avaldamismärge: RT II 2009, 22, 55 Eesti Vabarii
Väljaandja: Vabariigi Valitsus Akti liik: välisleping Teksti liik: algtekst Jõustumise kp: 06.08.2009 Avaldamismärge: RT II 2009, 22, 55 Eesti Vabariigi valitsuse ja Läti Vabariigi valitsuse toornafta
RohkemMicrosoft Word - polkaudio 2010 hinnakiri
polkaudio 2010 hinnakiri HINNAKIRI 2010 Kirjeldus Viimistlus Hinna Hind EEK Hind ühik 20%km 20%km naturaalne LSi SEEERIA spoon LSi 15 Põrandakõlar või kirss tk. 11344 725 LSi 9 Riiulikõlar või kirss paar
Rohkem(Microsoft PowerPoint - Town Centre Futures 2 Steve Kemp.ppt [\334hilduvusre\376iim])
What is the future for our town centres? Steve Kemp, Director, Globe Consultants International Ltd Mis on meie linnakeskuste tulevik? Steve Kemp, juhataja, Globe Consultants International Ltd Town centres:
RohkemEESTI STANDARD EVS-ISO/IEC 27000:2015 This document is a preview generated by EVS INFOTEHNOLOOGIA Turbemeetodid Infoturbe halduse süsteemid Ülevaade j
EESTI STANDARD INFOTEHNOLOOGIA Turbemeetodid Infoturbe halduse süsteemid Ülevaade ja sõnavara Information technology Security techniques Information security management systems Overview and vocabulary
RohkemMagnetic MRO
3D-tehnoloogiad õhusõidukite hoolduses 3D Printimine / Virtuaalreaalsus/ 3D Skänneerimine Pärtel-Peeter Kruuv Interior Workshop supervisor Magnetic MRO Arendused: mis mõjutab, mida rakendada? IT Google
Rohkem